This page was exported from Braindump2go Exam Dumps Free Download
[
https://www.pass4surevce.com
]
Export date: Thu Mar 28 23:13:26 2024 / +0000 GMT
2018/July New 200-125 Exam Dumps with PDF and VCE Free Updated Today! Following are some new 200-125 Real Exam Questions: QUESTION 286 A. CPU utilization Answer: ABC QUESTION 287 A. It identifies the source of a Type 1 LSA. Answer: AD QUESTION 288 A. speed Answer: B QUESTION 289 A. It is less CPU intensive for routers in the single area. Answer: BC QUESTION 290 A. interface FastEthernet 0/3 Answer: B QUESTION 291 A. SW1's Fa0/1 interface is administratively shut down. Answer: D QUESTION 292 A. It requires the use of ARP. Answer: BD QUESTION 293 A. exstart state > loading state > exchange state > full state Answer: B QUESTION 294 A. the port-channel 1 interface Answer: A QUESTION 295 A. 192.168.1.1 Answer: D QUESTION 296 A. router ospf area 0 Answer: C 1.|2018 Latest 200-125 Exam Dumps (PDF & VCE) 1084Q&As Download: https://www.braindump2go.com/200-125.html 2.|2018 Latest 200-125 Exam Questions & Answers Download: https://drive.google.com/drive/folders/0B75b5xYLjSSNanR4T1lPU1l5cmM?usp=sharing
What are three factors a network administrator must consider before implementing Netflow in the network? (Choose three.)
B. where Netflow data will be sent
C. number of devices exporting Netflow data
D. port availability
E. SNMP version
F. WAN encapsulation
Which two statements about the OSPF Router ID are true? (Choose two.)
B. It should be the same on all routers in an OSPF routing instance.
C. By default, the lowest IP address on the router becomes the OSPF Router ID.
D. The router automatically chooses the IP address of a loopback as the OSPF Router ID.
E. It is created using the MAC Address of the loopback interface.
What parameter can be different on ports within an EtherChannel?
B. DTP negotiation settings
C. trunk encapsulation
D. duplex
What are two benefits of using a single OSPF area network design? (Choose two.)
B. It reduces the types of LSAs that are generated.
C. It removes the need for virtual links.
D. It increases LSA response times.
E. It reduces the number of required OSPF neighbor adjacencies.
Refer to the exhibit. What set of commands was configured on interface Fa0/3 to produce the given output?
channel-group 1 mode desirable
switchport trunk encapsulation dot1q
switchport mode trunk
B. interface FastEthernet 0/3
channel-group 2 mode passive
switchport trunk encapsulation dot1q
switchport mode trunk
C. interface FastEthernet 0/3
channel-group 2 mode active
switchport trunk encapsulation dot1q
switchport mode trunk
D. interface FastEthernet 0/3
channel-group 2 mode on
switchport trunk encapsulation dot1q
switchport mode trunk
Refer to the exhibit. If the devices produced the given output, what is the cause of the EtherChannel problem?
B. There is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
C. There is an MTU mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
D. There is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)
B. It can support multiple IPv6 subnets on a single link.
C. It supports up to 2 instances of OSPFv3 over a common link.
D. It routes over links rather than over networks.
When a router undergoes the exchange protocol within OSPF, in what order does it pass through each state?
B. exstart state > exchange state > loading state > full state
C. exstart state > full state > loading state > exchange state
D. loading state > exchange state > full state > exstart state
A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?
B. the highest number member interface
C. all member interfaces
D. the lowest number member interface
Refer to the exhibit. If the router Cisco returns the given output and has not had its router ID set manually, what value will OSPF use as its router ID?
B. 172.16.1.1
C. 1.1.1.1
D. 2.2.2.2
What command sequence will configure a router to run OSPF and add network 10.1.1.0 /24 to area 0?
network 10.1.1.0 255.255.255.0 area 0
B. router ospf
network 10.1.1.0 0.0.0.255
C. router ospf 1
network 10.1.1.0 0.0.0.255 area 0
D. router ospf area 0
network 10.1.1.0 0.0.0.255 area 0
E. router ospf
network 10.1.1.0 255.255.255.0 area 0
F. router ospf 1
network 10.1.1.0 0.0.0.255
!!!RECOMMEND!!!
Post date: 2018-07-23 09:03:22
Post date GMT: 2018-07-23 09:03:22
Post modified date: 2018-07-23 09:03:22
Post modified date GMT: 2018-07-23 09:03:22
Powered by [ Universal Post Manager ] plugin. MS Word saving format developed by gVectors Team www.gVectors.com